Tuesday, August 18, 2009

Hippity-Hop! every time I look at this project it sprouts several rabbit trails to (mis) lead me to more solutions! or problems... as perspective sometime defines them.

I was told once that "a thoroughly defined question IS an answer" so this question popped unbidden into my whirling brain. :
"why not make your repstrap JUST like your router?"

As anyone who has built the McWire has doubtlessly discovered, it has a large number of mechanical quirks, and several designed in oversites, even so, I have dutifully built it very similarly to that shown in the plans with an eye to interjecting my take on things that could be improved, but, it appears to have stalled as a project as those involved went on to other things.

with that in mind, if this 1/2 meter cube turns out to be cheap enough to build - I may document that and advance it as yet-another-way to build a RepStrap

So, then, since I have some 1x1 extrusion lying around I'll be assembling a 1/2 meter cube with the sanguino electronics/repstrap project in mind - I found some inexpensive brackets online today and this will keep my tinkering reflexes sharp while I save money/wait for parts/etc... I may set it up useing the 1/4 inch drive threads while I decide if I am feeling bold enough to try for linear stepper drives, or if they turn out to be cost prohibitive

Baldor Linear Steppers

I'm sure it'd take thier lowest rating motor, given the forces involved...
yadda yadda, I've said enough for this post

and so it goes...

Wednesday, August 12, 2009

Just a quick post: The frame is together and checked for straightness, and squareness...



The space between the top bar and the next one down is the data/electric bus and external connector area the wide bar below will support the precision guide rails for the "X" axis of the motion control assembly "Y"'s parts are on order for the coming week.

Tuesday, August 11, 2009

The frame is assembled, with all the parts on hand it took about 45 minutes.

Now, trueing it up will likely take much longer...

The google sketchup drawing below shows the assembly with the 4 "extra" bars installed at the bottom of the machine, this has been changed in the actual machine to the top of the frame.

The reasoning is thus: they are to enclose the power, data, and logic housed in the machine i.e. the on-board controller (PLC probably), power bus, power connectors, data bus and data interface.

If the cube is applied to a "wet" process where substances can spill, and all that gadgetry is at the bottom....

So... I put all the power, data etc at the top where this is less relevant. (assuming we don't operate in a zero G enviroment -heh ;-) )

Also in the current design a pallet transporter is incorporated at the bottom of the cube but this is not shown yet as I have not worked out how to integrate the LIM (Linear Induction Motor)controls as a 4th axis, or weather the pallet will "park" and lockdown in some types of cells.

.
As an adjunct to the previous post here are some pics of the current "Cube" in progress


Those on the left are the frame:
(16) 1.5"x1.5" pieces 36.37 inches long,
(12) center tapped (4) not tapped


on the right (4) 3x1.5" pieces with aluminum angle braces, cheapo backing nuts and assorted hardware









This is a "Face" of the frame about to be assembled











A couple Frames










Almost together








I'll add more detail later, after assembly is completed.

.

Sunday, August 9, 2009

The trip so far:
I'm taking a low-budget journey from being shop-less to having light CNC capability with hopes for some automation as well
thus far I have built about 6 sanguinos, the McWire Repstrap, and a bunch of shop related stuff - the McWire got bogged down in a sanguino related problem and has been idled for a couple months ;-(
everything appears to work - and replicatorG control Software will move the motors as commanded, (albiet too slowly) but at the end of the G-Code it reports that the firmware version is 0.1 and refuses to run until restarted... attempts to re-load the bootloader or firmware have failed thus far....

it has been a low priority as there are several other projects on-going:

1) Water Condenser.
Since this is south central Texas its intolerably hot most of the time and quite humid as well, so: An experiment in extracting atmospheric water. A 50 dollar used de-humidifier, a few buckets and some tubing...

This week I extracted 20 gallons more water than was needed to water the herb garden...

The water is slightly cloudy, so, next: get it tested and determine what RO (Reverse Osmosis) filter kit will render it clean enough for storage, and if, post filtration, it will require sterilization via ozone or UV. Once the water is clean enough to store, then testing for contaminants and either a solar still or a post storage RO filter array to attempt to get it to a potable status, then add solar panels to make it stand alone. Rearrange the internal airflow to pre-cool the condensate air, (30% potential efficiency boost)and add a hot/cold appliance to the potable water branch of usage.... Celebrate with Coco! or Iced tea...

2) 1 Meter Cube, CNC Cell

something like this:


This thing is all built out of 80/20 aluminum Extrusion,

The goals are:

Modularity:
you should be able to connect several of these together and "assemble" all the steps to a manufacturing process

Replicatability:
i.e. a basic group of units should be able to make any part that is used in its construction - (Note: this is an obviously complex goal as in: drawing copper wire to wind motors etc) so in the shorter term making the aluminum connecting plates and such will serve as an analogue to a complete solution.

The working envelope is expected to be between 50% and 70% of the cubes volume.

Standardization: get the most function with the lowest part count.

I'll be adapting the Pilot Pro motion components to add CNC to this Cube

Other cubes under research...
PCB mill
Pick and Place
Vacuum forming
Electric Arc Furnace



More Later:
I am starting this Blog to document the progress of a robotics project,
to: accumulate and share technical triumphs and disasters.
and at some future point, to (potentially) attract others with similar ideas to move it all forward... ;)